Dirty Down Verdigris Effect – 25ml

The dark coloured liquiddries to a high matt verdigris colourin 1 to 5 minutes depending on the temperature. Apply verdigris paint bybrushorairbrush/sprayer.Verdigris effect paint looks best when applied torough, textured surfaces.Usage Instructions:
Thepot and surface should be atroom temperature or warmer before use. The verdigris colour may not appear if the pot and/or the surface are very cold.
The mixture will settle on the bottom of the pot. It’s very important to thoroughly shakethe pot with the ball bearings rattling before each and every use. Thoroughly stir the mixture and ensure that solids on the bottom of the pot are fully mixed into the liquid. Repeat stirring and shaking until all lumps have gone. It’s much better to shake and stir verdigris paint when the pot is at room temperature or warmer. If the pot is cold it may not be possible to fully mix any solids into the liquid.
Use verdigris paint straight from the pot.Replace the lid quickly during use to prevent the liquid from evaporating or decant what you need to use for a job into a separate smaller pot/container with a lid.
Do not add water into the paint pot – this may prevent the colour from forming.
Ensure surfaces are clean, dry and grease free.Test the paint on hidden surfaces before use to ensure compatibility and adhesion.
Only apply to non-porous surfaces such as plastic and metal. Do not apply to porous/absorbent surfaces such as bare timber or paper. Verdigris paint can be applied to painted surfaces, but test first. If the effect does not form, try first sealing the surface with varnish.
Verdigris paint iswater soluble and the effects of painting will be lost by washing in water or by getting wet, but there may still be staining. Do not expose verdigris paint to rain or splashing with water.
Verdigris paint looks best when applied to a rough surface.
Tofill dents and groovesin surfaces, first cover the surface with verdigris paint, and then wipe the paint off the raised areas with a damp cloth (at an angle to the grooves), leaving some of the paint trapped. The wetter the cloth, the more paint removed.
When fully dry, verdigris paint can be made more permanent by spraying with fine/mist coats of acrylic varnish/lacquer. Test varnish first because types of varnish change the colour/shade of the paint.
When dry, avoid scuffing/scratching the finished paintwork.

For the best results it’s best to practise different techniques listed below before final use.

To darken the shade apply more coats. Allow each coat to fully dry before applying another. Any number of coats of verdigris paint can be applied over the top of each other. For a broken, patchy effectapply to small areas/patches at a time and allow to dry – more in some areas, less in others.
The shade will vary depending on the quantity applied. A thick coat of paint will dry a darker shade, and a thin coat of paint will dry alightershade.
Further variations in shade can be created by dabbing a damp or wet brush, cloth or tissue onto the painted surface and then leaving to dry. As the water dries, the dye in the paint separates into shades of light and dark verdigris. The more water used, the greater the effect. This technique can be used after the paint has dried or while it is still wet. Another option is to simply splash water onto the verdigris paint and leave to dry – without dabbing.
For a very dark shade, decant a small amount into a separate pot and allow the paint to evaporate. The more the paint evaporates, the thicker and darker the paint gets (may not be possible to spray if too thick).

Brush Application

Dip the brush and immediately apply to the surface. For a patchy effect dab the paint onto a surface and keep dabbing in the same place until the paint dries. Any number of coats can be applied in this way. For a more even effect paint an even coat onto a surface.
A different verdigris effect is obtained depending on whether a soft or stiff brush used to apply the paint.

Fine Soft Brush: For very detailed work. Apply a small amount to the brush and apply directly to the surface.
Larger Soft Brush: For apply larger amounts to larger areas. For a darker shade apply larger quantities and for lighter shades apply smaller quantities.
Stiff Brush: Very light shades can be obtained by dabbing a very small quantity of verdigris paint onto a surface using a stiff brush. Allow verdigris paint to dry slightly on the brush for a very light effect, similar to the “dry brushing” painting technique.

Always clean the brush in water straight after use. Do not let verdigris paint fully harden onto brush. If for any reason verdigris paint has dried onto a brush, soak the brush in methylated spirits to fully clean, (but check first that this will not damage the brush).

Cloth/Tissue Application

Pour on a cloth or tissue and dab onto a surface and keep dabbing in the same place until the paint dries.
For a light shade apply a small amount at a time. For a darker shade apply a larger quantity.

Spray Application

Spray verdigris paint onto a surface straight from the pot using an air brush orpressure pot spray gun. Clean air brush immediately after use.

Verdigris Effect is water soluble. Verdigris Effect can be wiped off surfaces in two ways (even when fully dry):

Using a damp cotton bud.

Only dampen one end of the cotton bud.
Wipe verdigris paint with the damp end first, and then with the dry end.
The wetter the cotton bud, the more verdigris paint is removed.

Using a sheet of kitchen roll (absorbent paper towel).

First apply verdigris paint onto the panels so that they are fully covered, and leave to dry.
Flatter one end of a piece of kitchen roll, and dip this end into water.
Remove most of the water from the flat end so that it’s only slight damp. This can be done by pushing the flat end against other dry pieces of kitchen roll.
Gently press the damp flat end of kitchen roll against the dried verdigris paint, and twist the kitchen roll.
Keep the kitchen roll in one place, do not wipe side to side across the surface. Some verdigris paint is left on the model and some removed. Some verdigris paint will have been wetted by the damp kitchen roll and will change shade to look darker, just like old verdigris.
The wetter the verdigris paint gets, the darker the shade. Practice first to check how damp the kitchen roll should be and how much pressure to apply.

Create different shades of verdigris using water:

Apply verdigris paint to a surface.
Apply a small amount of water to the verdigris paint and either allow to dry on its own, or dry by dabbing with a piece of kitchen roll or tissue. This usually causes the colours to separate and dry different shades and more patchy.
Water can be applied to the surface after the verdigris paint has fully dried or when the verdigris paint is still wet.